This matches the dual lens brake light camera with our MON5000 dash monitor. The dual lens camera is designed to show a constant view when travelling forward and will switch to the downward facing camera when you go into reverse. Both lenses use a high quality 700 TVL CMOS sensor to give a good colour picture during the day and a black and white one at night. The night view for the reversing camera is aided by IR LEDs on the camera. The rear facing camera will depend on street lighting for a image.
Driving camera (upper camera)
- Sensor: 1/3 PC4089 CMOS
- Effective Pixels: 976(H) x 592(V)
- TV line: 580 TVL
- TV system: NTSC/PAL depending on the batch (if important please email to check)
- Lens: 2.6mm
- Min illumination: 0.1 LUX
- Waterproof: IP68
- View angle: V 65 degrees, H 80 degrees D 105 degrees
- Camera lens adjustment: 20 degrees up and down
- Voltage: 12 volts
- Current consumption: 150mA
- Operating temperature: -20 to 70 degrees C
- Certificates: FCC, CE, E-mark, RoHS
- Connector: 4 pin aviation
Reversing camera (lower camera)
- Sensor: 1/3 PC4089 CMOS
- Effective Pixels: 976(H) x 592(V)
- TV line: 700 TVL
- TV system: NTSC/PAL depending on the batch (if important please email to check)
- Lens: 1.9mm
- Min illumination: 0.0 LUX (IR LED on)
- IR LEDs: 8 pcs
- Night vision: 10m
- Waterproof: IP68
- View angle: V 85 degrees, H 130 degrees D 160 degrees
- Camera lens adjustment: 20 degrees up and down
- Voltage: 12 volts
- Current consumption: 150mA
- Operating temperature: -20 to 70 degrees C
- Guideline: Optional (some have a trigger wire to select)
- Certificates: FCC, CE, E-mark, RoHS
- Connector: 4 pin aviation
On all of our reversing camera systems we have a wide variety of cable and power options. The information below shows you what each option means.
5m 7.5m 10m 12.5m 15m 20m
These are our standard 4 pin extension cables. These options allow you to select what length you need. They are listed in metres, to get the length in feet simply multiply by 3 to change. Having longer than you need will not affect the picture, any extra cable should be coiled loosely where it cannot get damaged.
10M 8mm link, 12.5M 8mm link, 15M 8mm link
These are our 12.5m or 15m cables with an 8mm link at the front of the cable - designed to disconnect to help running through any tight gaps, then reconnected at the end of the install once you are next to the monitor.
Lighter plug
A lighter plug is a useful aid to testing as system before you fit it. Some people will run their system off a lighter plug instead of hard wiring it in.
Bailey adaptor
We do an adaptor to fit the Waeco cables that are pre-installed in Bailey Motorhomes. It converts their cable into our standard 4 pin ones. We have single camera and dual camera versions.
Stand style bracket
This is useful on our HD series of monitors where a curved dash makes mounting the U-bracket difficult. It also makes it faster and easier to remove the monitor.
Easy wire fuse tap a.k.a "piggyback fuse holders"
These can be used to take power from the fuse board. The earth should be to a point where there is bare metal to the vehicle body. The cable is about 2M long and terminates in a 2.1mm/5.5mm power plug, which fits in to the corresponding socket on the monitor wiring. We stock these in different blade sizes, please select the type of fuse tap that is fitted to your fusebox.
